機械設計外文翻譯-位置指示器用于煉鋼爐液壓泥炮的設計【中文2430字】【PDF+中文WORD】

機械設計外文翻譯-位置指示器用于煉鋼爐液壓泥炮的設計【中文2430字】【PDF+中文WORD】,中文2430字,PDF+中文WORD,機械設計,外文,翻譯,位置,指示器,用于,煉鋼爐,液壓,設計,中文,2430,PDF,WORD 【中文2430字】 位置指示器用于煉鋼爐液壓泥炮的設計 文摘:如何在煉鐵高爐設備中顯示液壓泥炮的位置準確是一個大問題。在本文中液壓粘土的位置指標基于渦輪流量傳感器和槍系統以AT89S52單身提出了處理器和一個誤差補償算法用于提高了測量精度。一個技術的數據轉儲也描述。整個系統可以避免不良環境的影響,而高爐設備工作。 關鍵詞:液壓泥炮;位置指標;渦輪流傳感器;89s52;誤差補償;數據轉儲。 1介紹 當鋼液從爐中流出,通過在耐火層里鉆一個洞。粘土槍是用來塞孔耐火粘土混合。有兩種粘土槍:電動泥炮和在iron-melting高爐液壓泥炮設備。如今,廣泛使用的粘土槍后者為了工作的影響條件。當鐵從煉鋼爐倒下來時爐、車間的溫度上升立即,空氣變得塵土飛揚,車間成為低能見度。一些機械的位置指標等方軸指針,重錘指針和彈簧采用指針指示活塞在汽缸的位置。所有這些指標低壽命;高故障比率和低由于糟糕的工作環境的靈活性條件。一個明顯的問題是,數據不能被記錄,所以很難說誰是罪魁禍首有一個事故。在本文中,指標體系為數據采集提供了一個框架,處理和監控已被研究和應用在煉鋼高爐液壓泥炮系統爐。 2原則、框架和問題 2.1系統原理 考慮工作的不良影響條件、渦輪流量傳感器用來獲得活塞的間接信息。渦輪流傳感器是用于水流入或損失測量。渦輪機轉動頻率(F)與流量成正比的速度(V)即數量(Q)液體流動的相應氣缸的一部分。在每個渦輪機轉動傳感器發送通過電纜脈沖計數器。然后氣缸的容積可以得到的脈沖數。K = F / Q或K = N / V(1),增殖系數代表的數量的輸出脈沖傳輸每加侖的液體通過渦輪流量計。每個渦輪機都有一個獨特的增殖系數。N代表了總脈沖數。每一個脈沖生成代表一個離散量的體積吞吐量。 2.2系統框架 在此系統中,兩個獨立的單向的閥門和傳感器安裝在管道系統流量的信息數據采樣、處理、在單片機顯示和交通管理。一個上電腦是用于監視當前工作地位和在線或離線達達處理。兩種顯示用于運營商。系統的主要框架如下: 圖1 框架的位置指標 核心系統組件的詳細以下描述的專業子系統形成了功能齊全的操作環境。 2.3主要問題 采用渦輪流量傳感器可以逃避可怕的環境,但也會導致一些問題 1) 如何避免由于舍入誤差編程和彌補差距之間的來回運動的活塞將兩個傳感器的區別是主要的系統的問題。 2) 系統應該是簡單和容易操作沒有帶來了復雜性主系統。 3) 集成系統應包括數據采樣、處理、顯示和監控。 3降低電腦 3.1系統的工作模式 該系統可以在三個不同的操作根據不同的工作時間模式液壓泥炮。 a、校準模式。這使得系統普遍的。缸的總脈沖數在這種模式下獲得的。 b、填塞模式。在這種模式下,工人的東西汽缸的粘土緊張的方式。的信息可以看到活塞的裝載機、運營商和監視器。 c、擠壓模式。在這種模式下,工人出鐵口擠出的泥醬。主要的和在這種模式下,也重要的數據采樣被顯示。 3.2控制器Block-Diagram 核心處理單元是基于法。法是一種低功耗、高性能CMOS 8位單片機8 kb字節的細節可編程閃存。的以AT89S52還提供了以下特點:8 k32字節的flash,256字節的內存,I / O線,看門狗定時器,兩個數據指針,三個16位定時器/計數器,six-vector兩級中斷架構,一個全雙工串行端口,芯片上振蕩器和時鐘電路。系統的控制器block-diagram一樣 如下: 圖2 控制器block-diagram 整個控制block-diagram由以下元素:的誕生是用來獲得的信息數量的液體和發送脈沖。-AT89S52用于控制數據流搗固、擠壓和校準和給予適當的信息顯示、報警和與上面的電腦交流?！猂S232和RS485通信協議用于數據傳輸。在此系統中,使用兩種領導是在里面,外面,另一個是。 3.3傳輸數據上電腦 使系統更普遍,RS232并采用RS485通信協議。RS232提供單端數據通信發射機和接收機之間相對緩慢數據速率(115 k位/秒)和短距離(50英尺的最大數據速率)。RS485鏈接提供更多的遠距離通信的可靠性高速工業工廠。采用RS485需要安裝一個RS485通信協議接口擴展槽的計算機或轉換信號出來的RS232水平計算機串口的RS485信號。一個介紹RS232 / RS485轉換器系統。 3.4實現的軟件 軟件部分可以包括幾個部分:計算、計算、通信和監控。 3.4.1校準 總脈沖數是不同的不同的氣缸。校準過程單向的總脈沖數的移動活塞。用于提高平均計算系統的精度。如果總步數安排,用于的步長數計數器的初始計算數量和剩余將獲得的數量?？赡苡袃蓚€不同初始統計數字分開計數器用于或移動因為單獨的渦輪傳感器。方法之一的程序流程圖如下: 圖3 校正流程圖 3.4.2計數 課程,一個計數器(T0)隨活塞的口液壓泥炮,而落后的計數器(T1)增加與活塞撤退計數器(T0)保持相同。 計數器(T0)的程序如下: T0INT:… INC 5布式硬度 INC 31H;當前步驟注冊、低一些 INC 6AH;臨時步驟注冊 MOV A,31H CJNE A,#00H,DDD0 INC 30H;當前步驟注冊、高一些 3.4.3誤差補償 圖4 提出賠償 以下使用誤差補償來彌補在計算剩余數量的影響。如果號碼分配100步,是肯定的脈沖的數量并不總是整數和每一步剩余數量可能被忽略。這是說, 總計算步驟是低于實際的步驟。一旦活塞一次又一次,一個巨大的錯誤將會發生。一個誤差補償算法介紹了向前和向后運動。一個臨時步驟注冊使用的在活塞補償計算每個脈沖移動。曾經被認為是一個補償步驟,清除臨時寄存器,步重新開始計數準備下一個補償。向前,反向補償流程圖如下: 圖5 落后補償 3.4.4監控 監控系統是用來好好利用歷史和當前數據和給予指令來操作和管理。Auto-analysis歷史數據將提供最佳的填料和擠壓。的優化過程也可以人工完成。 4數據分析 在系統中,提出了兩種類型的數據處理,使之更普遍。一個是spot-workers,這使得他們操作操縱桿正確。另一個是為經理人員進一步分析得到的最優數量搗固和擠壓。 4.1在線數據處理 系統提供實時的軟件測量脈沖轉化為位移,通過應用校準和執行計算。 4.2離線數據分析 可以交互地分析和歸檔數據可視化的幫助下一個通用的數據分析程序。這個程序可以用于繪制個人數據的波形以及渠道執行簡單的數學操作單或結合波形。用戶可以擴展通過添加任何自定義處理能力算法。 5結論 誤差補償算法系統可靠。系統已經關閉了成功地應用于監控的工作狀態液壓泥炮?；A上的經驗工人的證實,該系統是真實的,靈活、可重構、可伸長的、可伸縮的。 參考文獻 [1]Fuehan, R. J.,etc.The Future Steelmaking Industry and ItsTechnologies, INEL-95/0046, Idaho National EngineeringLaboratory, Idaho Falls, Idaho,December 1994 [2]Quanlinyue, The application of Turbine Flow in FlowMeasurement in Waterworks, Process AutomationInstrumentation, Vol.23,No.12,2002 [3]SPONSLER CO.,INC, Turbine flowmeters for liquidmeasurement, 2002 [4]ATMEL Corporation, 89S52, 2005 [5]S.Sharonov, J.M.Nogiec, An Embedded Power SupplyController, Pac’97, Vancouver, 1997 [6]J.M.Nogiec, E.Desavouret, etc. A Distributed Monitoringand Control System, IEEE, 1998, 3713~3715 [7]Tang hui, A Flow Rate Monitoring Meter Based-on 8098 Single Chip Computer, Instrument technology and Sensors,Vol.3,1996 The Seventh International Conference on Electronic Measurement and Instruments ICEMI2005 2-207Design of Position Indicator Used for Hydraulic Clay Gun in Steel-making Furnace Lin Quanxi1 Dou Manfeng1 Zheng Yayin2 Liu Gequn1（1.Northwestern Polytechnical University，Xian 710072 China）(2.Beijing Jiaotong University,Beijing 100044 China)Abstract:How to indicate the position of hydraulic clay gun accurately is a big problem in iron-smelting blast furnace equipments.In this paper,a position indictor of hydraulic clay gun system based on turbine flow sensors and AT89S52 single processor are presented and an error compensation algorithm which used to improve the measure precision is investigated.A technic of data dump is also described.The whole system can avoid the influence of bad environment while the blast furnace equipment working.Keywords:Hydraulic clay gun;position indictor;turbine flow sensors;89S52;error compensation;data dump.1 Introduction When molten steel is removed from the furnace,a hole is drilled through the refractory liner.A clay gun is used to plug the hole with a refractory clay mix.There are two kinds of clay gun:electric clay gun and hydraulic clay gun in iron-melting blast furnace equipments.Nowadays,the widely used clay gun is the latter for the sake of the influence of the working condition.When iron water is poured down from blast furnace,the temperature of the workshop rises immediately,the air becomes dusty,and the workshop becomes poor visibility.Some mechanical position indictors such as square shaft pointer,heavy hammer pointer and spring pointer are adopted to indicate the position of piston in the cylinder.All these indictors are low life-span;high malfunction ratio and low environment flexibility due to the bad working condition.A noticeable problem is that the data cannot be recorded,so its hard to tell who is to blame once there is an accident.In this paper,a position indictor system which provides a framework for data acquisition,disposal and monitoring has been investigated and applied to the hydraulic clay gun system in steel-making blast furnace.2 Principle,Framework and Problems 2.1 System Principle Considering the bad influence of the working condition,turbine flow sensors are used to obtain the information of the piston indirectly.Turbine flow sensor is used for water inflow or water loss measuring.Turbine rotation frequency(F)is proportional to flow speed(V)i.e.to the quantity(Q)of liquid flow in corresponding part of the cylinder.At every turbine turn the sensor sends through the cable a pulse to the counter.Then the cubage of the cylinder can be gotten from the pulse number.K=F/Q or K=N/V (1)The K-Factor represents the number of output pulses transmitted per gallon of fluid passing through the turbine meter.Each turbine has a unique K-Factor.N represents the total pulse number.Each pulse generated represents a discrete amount of volumetric throughput.2.2 System Framework In this system,two separate set of one-way valves and sensors are equipped in the ductwork to get the information of flowrate.Data sampling,disposal,display and transit are managed in MCU.An upper computer is used for monitoring the current working status and giving the online or offline dada processing.Two kinds of displays are used for the operators.The The Seventh International Conference on Electronic Measurement and Instruments ICEMI2005 2-208main framework of the system is as follows:pumpoilreservoirone way valvesensor1one way valvesensor2hydraulic cylindersamplingMCUdisplayuppercomputer Fig.1 Framework of the position indictor The core system components are detailed in the following descriptions by specialized subsystems to form the full-featured operating environment.2.3 Main Problems Adopting the turbine flow sensors can evade the awful environment,but it also causes some problems.1)How to avoid the rounding error which is due to the programming and make up with the disparity between the back and forth motion of the piston which is due to the difference of the two sensors is the main problem of the system.2)The system should be simple and easily operated without bringing much complexity to the primary system.3)The integrated system should involve data sampling,disposal,display,and monitoring.3 Lower Computer 3.1 Working Mode of the System The system can be operated in three different modes according to the different working period for the hydraulic clay gun.a)Calibration Mode.This makes the system universal.The total pulse number of the cylinder is obtained in this mode.b)Tamping Mode.In this mode,workers stuff the cylinder with clay in a tight way.The information of the piston can be seen by the loaders,operators and monitors.C)Extrusion Mode.In this mode,workers extrude the clay to jam the taphole.The main and important data is sampled during this mode and also be displayed.3.2 Controller Block-Diagram The core processing unit is based on the AT89S52.The AT89S52 is a low-power,high performance CMOS 8-bit microcontroller with 8Kb bytes of in-system programmable flash memory.The AT89S52 also provides the following features:8K bytes of flash,256 bytes of RAM,32 I/O lines,watchdog timer,two data pointers,three 16-bit timer/counters,a six-vector two-level interrupt architecture,a full duplex serial port,on-chip oscillator,and clock circuitry.The controller block-diagram of the system is as follows:AT89S52T0(P3.4)T1(P3.5)P0.0P0.1 P0.6P0.7RXD(P3.0)TXD(P3.1)RESETXTAL1XTAL2sensor1sensor2Opto-couple circuitOpto-couple circuit8155PAPBLED1LED2RS232 andRS485PCP1.2P1.3P1.4satus displayINT0INT1TampingExtrusionAD0AD1.AD7CalibrationP1.0P1.5P1.6P1.7 Fig.2 Controller block-diagram The whole control block-diagram consists of the following elements:-Sensors are used to get the information of the quantity of liquid and send pulses.-AT89S52 is used to control the data flow of tamping,extrusion and calibration,and to give the proper information of displaying,alerting and communicating with the upper computer.-Both RS232 and RS485 communication protocols are used for data transmitting.-Two kinds of LED are used in this system,one is for the inside,and the other is for the outside.3.3 Transmitting Data to Upper Computer To make the system more universal,both RS232 and RS485 communication protocols are adopted.RS232 provides single-ended data communications between a transmitter and a receiver at relatively slow The Seventh International Conference on Electronic Measurement and Instruments ICEMI2005 2-209data rates(115k bits/second)and short distances(up to 50 ft at the maximum data rate).RS485 links provide more communication reliability over a long distance at a high speed for industrial plants.Adopted RS485 communication protocol needs to install an RS485 interface in an expansion slot of the computer or to convert the RS232 level signal coming out the computer serial port to an RS485 signal.A RS232/RS485 converter is introduced in this system.3.4 Implementation For Software The software part can be included several parts:calculation,counting,communication and monitoring.3.4.1 Calibration The total pulse numbers are different with different cylinders.The calibration process is to get the total pulse number of one-way moving of the piston.An average calculation is used to improve the precision of the system.If total step number is arranged,the step length number which used for the initial count number of the counter and residual number will be obtained.There are probably two different initial count numbers for the separate counters used for the forth or back moving because of the separate turbine sensors.The program flow chart for one way is as follows:calibrationaveragesingle counting sumstep lengthnumberresidualnumberstep numberinitial countingnumber for timer Fig.3 Calibration flow chart 3.4.2 Counting For the forward course,one counter(T0)increases with the piston moves to the mouth of the hydraulic clay gun,while for the backward,the other counter(T1)increases with the piston retreats and the counter(T0)keeps the same.The program for the counter(T0)is as follows:T0INT:INC 5BH INC 31H;current step register,low bit INC 6AH;temp step register MOV A,31H CJNE A,#00H,DDD0 INC 30H;current step register,high bit 3.4.3 Error compensation integral part(I)average(eg:100 share)residual part(R)sumtemporary stepnumber(T)average(eg:100 share)(A)clear temporary stepregister(T=0)subtract 1 from currentstep register(C)return0YesNoR*T-I*A Fig.4 Forward compensation The following error compensation is used to make up the influence of residual number while calculating.If the step number is assigned 100,it is sure that the pulse number of every step is not always integer and the residual number may be ignored.Thats to say,the The Seventh International Conference on Electronic Measurement and Instruments ICEMI2005 2-210total counting step is less than the actual total steps.Once the piston moves again and again,a great error will occur.An error compensation algorithm is introduced for the forward and backward motion.A temporary step register which used for the compensation counts every pulse during the piston moving.Once one compensation step is considered,clear the temporary step registers,restart counting and prepare for the next compensation.Forward and backward compensation flow charts are as follows:integral part(I)average(eg:100 share)residual part(R)sumtemporary stepnumber(T)average(eg:100 share)(A)clear temporary stepregister(T=0)pluse 1 from currentstep register(C)return0YesNoR*T-I*A Fig.5 Backward compensation 3.4.4 Monitoring A remote monitor system is used to take good advantage of historical and current data and give instructions to operation and management.Auto-analysis of historical data will provide the optimum amount of stuffing and extrusion.The optimization process can also be done artificially.4 Data Analysis In the system,two kinds of data processing are presented to make it more universal.One is for the spot-workers,which makes them operate the joy stick correctly.The other is for the manager worker for a further analysis to get an optimum amount for tamping and extrusion.4.1 On-line Data Processing The software system provides for real-time conversion of measured pulses to displacement,by applying calibrations and performing calculations.4.2 Off-line Data Analysis Archived data can be interactively analyzed and visualized with the help of a universal data analysis program.This program can be used for plotting waveforms of individual data channels as well as for performing simple mathematical operations on single or combined waveforms.The user can extend the processing capabilities by adding any custom algorithms.5 Conclusions The error compensation algorithm makes the system reliable.The system has been already successfully applied to monitor the working status of hydraulic clay gun.The experience based on the workers confirms that the system is veracious,flexible,reconfigurable,extendible,and scalable.Reference 1Fuehan,R.J.,etc.The Future Steelmaking Industry and Its Technologies,INEL-95/0046,Idaho National Engineering Laboratory,Idaho Falls,Idaho,December 1994 2Quan linyue,The application of Turbine Flow in Flow Measurement in Waterworks,Process Automation Instrumentation,Vol.23,No.12,2002 3SPONSLER CO.,INC,Turbine flowmeters for liquid measurement,2002 4ATMEL Corporation,89S52,2005 5S.Sharonov,J.M.Nogiec,An Embedded Power Supply Controller,Pac97,Vancouver,1997 6J.M.Nogiec,E.Desavouret,etc.A Distributed Monitoring and Control System,IEEE,1998,37133715 7Tang hui,A Flow Rate Monitoring Meter Based-on 8098 The Seventh International Conference on Electronic Measurement and Instruments ICEMI2005 2-211Single Chip Computer,Instrument technology and Sensors,Vol.3,1996 Author Biographies Lin Quan-xi(1979),male,received the electromechanical B.S.degree in ShenYang Institute of Aeronautical Engineering,ShenYang,China,in 2002.Currently he is a master candidate in the department of electric machine&electric engineering of Northwestern Polytechnology University,Shannxi,China,mostly pursues the research of rare earth motor design and motion control.Dou Man-feng(1967),male,received the B.S.,M.E.and Ph.D degrees in Electronic Engineering from Northwestern Polytechnology University,Shannxi,China.He is currently a professor.His research interests are power electronics,motor design,motor drives,electrical machine and motion control system.Zheng Ya-yin(1978),male,received the electromechanical degree B.S.degree in ShenYang Institute of Aeronautical Engineering,ShenYang,China,in 2002.Currently he is a master candidate in the department of Electronic Engineering of Beijing Jiaotong University,Beijing China,mostly pursues the research of detecting and measuring.Liu Ge-qun,male,received the M.Eng.degrees in Control Theory and Engineering from Northwestern Polytechnical University,Xian,China,in 2003.He is currently a doctor candidate in the Automation College,Northwestern Polytechnical University,Xian,China.His research interests include Modern Control Theory,Intelligent Control,and Flight Control Systems.